COVID...stay healthy

General topics...if a particular user would like their own sub-area, please let me know!
Post Reply
User avatar
LePaul
Reactions:
Posts: 3455
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

COVID...stay healthy

Post by LePaul » March 19th, 2020, 12:42 pm

I've been working from home for a week, since I traveled West where there were infections.

But so far, I am fine

And getting a lot of 3D printing done :-)

User avatar
Roberts_Clif
Reactions:
Posts: 960
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: COVID...stay healthy

Post by Roberts_Clif » March 21st, 2020, 9:20 am

Good to Hear that you are fine!
Last edited by Roberts_Clif on March 22nd, 2020, 8:59 am, edited 1 time in total.
Electronics Technician / Computer Programmer

Lez0
Reactions:
Posts: 135
Joined: October 8th, 2017, 10:21 am
Location: Spain
3D Printer(s): JGAurora A5S, Anycubic Photon

Re: COVID...stay healthy

Post by Lez0 » March 22nd, 2020, 3:59 am

Hi from Europe, I think we will be at home for quite a while, so let's start some new projects........

User avatar
LePaul
Reactions:
Posts: 3455
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

Re: COVID...stay healthy

Post by LePaul » March 22nd, 2020, 2:25 pm

I've been reading how hard Italy has been hit with Spain not far behind. Stay healthy!

User avatar
Roberts_Clif
Reactions:
Posts: 960
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: COVID...stay healthy

Post by Roberts_Clif » March 22nd, 2020, 6:31 pm

Yes was just discussing that very thing on another forum, I plan to finish up my MPCNC and to my first carving.
Also want to add the ability to have 3D Printing tools that can be plugged in when needed.
However this is the time of year when we have enough yard work to keep us busy for weeks on end.

Not to make this about the SARS-CoV-2, was already planning on continue when the weather got warmer anyway.
I have no place in the home for a noisy CNC, and needed a larger area like outside on a couple a saw horses.
Or better yet! A small shed with power, then will not have to stop when the weather gets bad again.
Electronics Technician / Computer Programmer

Lez0
Reactions:
Posts: 135
Joined: October 8th, 2017, 10:21 am
Location: Spain
3D Printer(s): JGAurora A5S, Anycubic Photon

Re: COVID...stay healthy

Post by Lez0 » March 23rd, 2020, 6:40 am

Yes Italy and Spain have been hit hard. You have to be careful so you are not next, avoid contact with others and stay indoors, and starting something new.

User avatar
Roberts_Clif
Reactions:
Posts: 960
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: COVID...stay healthy

Post by Roberts_Clif » March 24th, 2020, 3:35 pm

Went out to get a few supplies, groceries and house hold items they are going crazy out there.

The one store I went to had lines on the floor marked off at 6 foot intervals leading to the cash registers.
Social distancing and all the State and federal government said in order to keep the virus from spreading.
Did not even notice, who would have, got yelled at because went over the line by a foot by store customer.
The cashier at the checkout is way closer than 6' an they will spread the virus to more in one day than anyone.
Last edited by Roberts_Clif on March 24th, 2020, 10:04 pm, edited 1 time in total.
Electronics Technician / Computer Programmer

User avatar
LePaul
Reactions:
Posts: 3455
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

Re: COVID...stay healthy

Post by LePaul » March 24th, 2020, 7:54 pm

It's kinda like the movie Independence Day...minus the invading aliens!

User avatar
LePaul
Reactions:
Posts: 3455
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

Re: COVID...stay healthy

Post by LePaul » April 1st, 2020, 11:07 am

Hope everyone is staying healthy!
I have my FT-6 apart to install the E3D Hemera. Been doing a lot of prints on my Ultmaker 2+ and FT-5 How's everyone doing?

User avatar
Roberts_Clif
Reactions:
Posts: 960
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: COVID...stay healthy

Post by Roberts_Clif » April 1st, 2020, 3:26 pm

Hey @LePaul

Doing really good
Electronics Technician / Computer Programmer

User avatar
Roberts_Clif
Reactions:
Posts: 960
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: COVID...stay healthy

Post by Roberts_Clif » April 8th, 2020, 10:07 am

China's Wuhan couples were so eager to marry after lockdown ended that they crashed the marriage application system.

Read more
Electronics Technician / Computer Programmer

Post Reply

Return to “General Discussion”