STL previewer?

Post Reply
User avatar
LePaul
Reactions:
Posts: 3403
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

STL previewer?

Post by LePaul » December 5th, 2016, 6:43 pm

I have a ton of files and rather than open each and every one in Cura....is there a good (Windows) program for previewing the STL files, similar to what we can do for photos?

User avatar
ivan.akapulko
Reactions:
Posts: 389
Joined: February 11th, 2016, 11:27 am
Location: Ust-Kamenogorsk, Kazakhstan
3D Printer(s): Ultimaker 2
Contact:

Re: STL previewer?

Post by ivan.akapulko » December 6th, 2016, 1:26 am


User avatar
LePaul
Reactions:
Posts: 3403
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

Re: STL previewer?

Post by LePaul » December 6th, 2016, 10:18 am

I'll check that out....I found another one that worked okay, all I had to do was go into Windows File Explorer, turn on the View to Large Icons and I could see the items!

User avatar
ivan.akapulko
Reactions:
Posts: 389
Joined: February 11th, 2016, 11:27 am
Location: Ust-Kamenogorsk, Kazakhstan
3D Printer(s): Ultimaker 2
Contact:

Re: STL previewer?

Post by ivan.akapulko » December 6th, 2016, 10:38 am

Can you share link?

User avatar
LePaul
Reactions:
Posts: 3403
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

Re: STL previewer?

Post by LePaul » December 6th, 2016, 10:43 am

This message board thread shows info on it

http://community.robo3d.com/index.php?t ... orer.7596/

The download link they list on the 3rd page is this

http://www.pragmaticdesigns.com/K-Studi ... .2.4.0.zip

I registered for a key to use the program...I didn't think to check if one was required or not for the previews to show!

User avatar
Chaco
Reactions:
Posts: 53
Joined: September 12th, 2016, 6:48 pm
Location: OH
3D Printer(s): HyperCube & Hictop Prusa i3 3DP-08
Contact:

Re: STL previewer?

Post by Chaco » April 24th, 2019, 11:02 am

Just to have the info logged here for the future.... people should check out Papas STL viewer. This app is small and light, and just does exactly what you expect. Open and show STLs

User avatar
LePaul
Reactions:
Posts: 3403
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): UM2+,CR-10S (x2),Tevo Tornado,FT-i3/FT-5/FT-6...
Contact:

Re: STL previewer?

Post by LePaul » April 26th, 2019, 10:17 am

Yes! Way better than the robo3D thing

Post Reply

Return to “Other Slicing programs”