A Tea between friends :-) How was Your Day

General topics...if a particular user would like their own sub-area, please let me know!
User avatar
MTVDNA
Reactions:
Posts: 138
Joined: August 7th, 2016, 10:29 pm
Location: Netherlands
3D Printer(s): Ultimaker 2

Re: A Tea between friends :-) How was Your Day

Post by MTVDNA » May 31st, 2018, 3:08 am

LePaul wrote:
May 30th, 2018, 3:36 pm
Hey @MTVDNA , welcome back!
Thanks, never really have been gone though. I still read here regularly, but I haven't had much time to print anything lately so I haven't been posting much ;)

reibuehl
Reactions:
Posts: 458
Joined: February 9th, 2016, 9:56 am
Location: Stuttgart, Germany
3D Printer(s): Ultimaker 2

Re: A Tea between friends :-) How was Your Day

Post by reibuehl » May 31st, 2018, 6:45 am

For an upcoming motion detector based LED strip project I needed a way to enable/disable the whole solution so that it is only active during the night. So I fired up Fusion 360 and came up with this nice little case:
2018-05-31 11.21.00.jpg
It contains a Sonoff Basic with the Tasmota firmware for switching the power over MQTT from my home automation system and the PCB from the 12V wall wart power supply that came with the LED strip set:
2018-05-31 11.22.01.jpg
The case can be screwed to the wall and I used M3 brass inserts for the lid to avoid damaging the threads by using it too often.
Attachments
2018-05-31 11.21.51.jpg
Reiner.

User avatar
LePaul
Reactions:
Posts: 3099
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: A Tea between friends :-) How was Your Day

Post by LePaul » May 31st, 2018, 10:57 am

It's been fairly quiet here....I stop pop in a lot to see whose chatting...and I keep plugging the site in my YouTube videos (in the description text)

User avatar
ivan.akapulko
Reactions:
Posts: 388
Joined: February 11th, 2016, 11:27 am
Location: Ust-Kamenogorsk, Kazakhstan
3D Printer(s): Ultimaker 2
Contact:

Re: A Tea between friends :-) How was Your Day

Post by ivan.akapulko » June 10th, 2018, 11:39 pm

Hi, gang! Too much work atm. New job, new places, new hardware to support. Prepare for Siemens SCADA controllers and PCS7 certification.

User avatar
LePaul
Reactions:
Posts: 3099
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: A Tea between friends :-) How was Your Day

Post by LePaul » June 11th, 2018, 1:59 pm

Did you make your trip out here yet?

User avatar
ivan.akapulko
Reactions:
Posts: 388
Joined: February 11th, 2016, 11:27 am
Location: Ust-Kamenogorsk, Kazakhstan
3D Printer(s): Ultimaker 2
Contact:

Re: A Tea between friends :-) How was Your Day

Post by ivan.akapulko » June 18th, 2018, 11:57 pm

LePaul wrote:
June 11th, 2018, 1:59 pm
Did you make your trip out here yet?
Nope. It still in plans for vacation, closer to autumn, I think.

Post Reply

Return to “General Discussion”

Who is online

Users browsing this forum: No registered users and 7 guests