A Tea between friends :-) How was Your Day
- LePaul
- Reactions:
- Posts: 3982
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: A Tea between friends :-) How was Your Day
School is back in session here! (I work at a University so week one was super busy)
How is everyone?
How is everyone?
- LePaul
- Reactions:
- Posts: 3982
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: A Tea between friends :-) How was Your Day
I'm loving the Rivyt webpage system for YouTubers...check this out
http://wherenerdyiscool.rivyt.com/
http://wherenerdyiscool.rivyt.com/
- LePaul
- Reactions:
- Posts: 3982
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: A Tea between friends :-) How was Your Day
Well I decided to redirect my WhereNerdyIsCool.com site to rivyt I really like their service...and it saves me from messing with Wordpress
- jonnybischof
- Reactions:
- Posts: 310
- Joined: February 15th, 2016, 2:48 am
- Location: Zurich, Switzerland
- 3D Printer(s): UMO
Re: A Tea between friends :-) How was Your Day
That link doesn't work anymore btw.LePaul wrote: ↑September 7th, 2017, 1:20 pm I'm loving the Rivyt webpage system for YouTubers...check this out
http://wherenerdyiscool.rivyt.com/
www.WhereNerdyIsCool.com does.
It's a simple but cool page! Not too much clutter and stuff you have to care about, only content.
- LePaul
- Reactions:
- Posts: 3982
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: A Tea between friends :-) How was Your Day
Yes that old link won't work since the name settings/Dns stuff took effect.
- Titus
- Reactions:
- Posts: 252
- Joined: February 9th, 2016, 10:20 pm
- 3D Printer(s): Ultimaker Original+HBK
Re: A Tea between friends :-) How was Your Day
Interesting:
https://i.imgur.com/tmkcTwU.jpg
Not quite what I expected. Especially not the, from what it seems, different sanding directions?
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: A Tea between friends :-) How was Your Day
Change default speed to avoid overheating the print. It’s hidden inside speed settings
- Titus
- Reactions:
- Posts: 252
- Joined: February 9th, 2016, 10:20 pm
- 3D Printer(s): Ultimaker Original+HBK
Re: A Tea between friends :-) How was Your Day
It was 20 mm/s, which I couldn't image to be right(I'm printing at 60 mm/s), so I changed it to 60 mm/s too. Do you recon I should go even faster for the Neosanding speed?
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: A Tea between friends :-) How was Your Day
Yea. Faster. For 50-60 I do 100mm/s sanding
Slower only helps if your top layers show too many gaps on the top layer surface. Fast will leave a nice look and you can increase the passes without loosing much time
Slower only helps if your top layers show too many gaps on the top layer surface. Fast will leave a nice look and you can increase the passes without loosing much time
- LePaul
- Reactions:
- Posts: 3982
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: A Tea between friends :-) How was Your Day
I've been meaning to try out that feature
- Titus
- Reactions:
- Posts: 252
- Joined: February 9th, 2016, 10:20 pm
- 3D Printer(s): Ultimaker Original+HBK
Re: A Tea between friends :-) How was Your Day
https://ultimaker.com/en/blog/51255-com ... e-releases
Not sure who or where someone hinted at something upcoming, might be this.
Not sure who or where someone hinted at something upcoming, might be this.
- LePaul
- Reactions:
- Posts: 3982
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: A Tea between friends :-) How was Your Day
I thought we might have a new machine coming up
Re: A Tea between friends :-) How was Your Day
And I was wondering why all the sudden there are random non-consistent underextrusions...
- Roberts_Clif
- Reactions:
- Posts: 1387
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: A Tea between friends :-) How was Your Day
I have from time to time when using multiple Slicers mess up My 3D Printer Marlin Firmware (I know most are using Teacup).shurik
Just Yesterday I Was Testing to see which of the Slicers would Allow me to send G-Code to the Printer.
When I started printing a Model it looked like Swish Cheese See Image.
Some how just by connecting and sending a couple of G-codes (for testing purposes) I mess up the Printer Filament Size.
And until I had sent a M502 and M500 every print looked the swish cheese.
Maybe something like this could have happened.