Make Magazine top printer and review

Prusa i3 printer discussion...the official one from Josef Prusa
Post Reply
User avatar
LePaul
Reactions:
Posts: 2847
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Make Magazine top printer and review

Post by LePaul » November 12th, 2016, 9:18 pm


User avatar
Izzy
Reactions:
Posts: 591
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Make Magazine top printer and review

Post by Izzy » November 13th, 2016, 8:50 am

I must admit I was looking at getting one of these and upgrading to the dual head printing, I'm still keeping my eye on it as I'm wondering on the nozzle side whether it can use the same as the Ultimaker or it can be upgraded to it and get a 1.75 Ruby for it.

:-D I've just won a Wanhao Duplicator i3 with filament directorys compertition, my wife is going to have a go with it :shock: so we are going to write a little piece for a blog as a complete novice starting into 3dPrinting :-)
Izzy.

User avatar
LePaul
Reactions:
Posts: 2847
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Make Magazine top printer and review

Post by LePaul » November 13th, 2016, 5:37 pm

I'm torn as well. I can buy three Prusa's for the price of one Ultimaker. Same quality, same (if not more responsive) support

User avatar
Izzy
Reactions:
Posts: 591
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Make Magazine top printer and review

Post by Izzy » November 13th, 2016, 5:57 pm

The prusa has an edge, and you can always build a cabinet cover for it. And it has dual or quad printing upgrade...
Izzy.

User avatar
LePaul
Reactions:
Posts: 2847
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Make Magazine top printer and review

Post by LePaul » November 13th, 2016, 6:13 pm

There's a 5-6 week wait for them, just checked their site! (The assembled and calibrated ones)

User avatar
nilrog
Reactions:
Posts: 395
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Make Magazine top printer and review

Post by nilrog » November 14th, 2016, 11:32 am

If the MkII had been out one year ago I would have bought one.

User avatar
LePaul
Reactions:
Posts: 2847
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Make Magazine top printer and review

Post by LePaul » November 17th, 2016, 3:58 pm


Post Reply

Return to “Original Prusa i3 MK2 printer”

Who is online

Users browsing this forum: No registered users and 1 guest