Marlin 1.1.4

Software and Firmware Discussion - related to source code, firmware updates, etc.
Post Reply
User avatar
Roberts_Clif
Reactions:
Posts: 400
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Marlin 1.1.4

Post by Roberts_Clif » August 27th, 2017, 5:22 pm

Now I have two Hictops one 12volt and One 24volt.
They have the same controller card they were both upgraded to Marlin 1.1.4-RC6 - they both have different problems.
The only firmware lines that are different are as follows.

RED
#define CUSTOM_MACHINE_NAME " HicRed 1.1.4 "
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 1600, 94.4962144 }

BLUE
#define CUSTOM_MACHINE_NAME " HicBlue 1.1.4 "
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 94.4962144 }

Both has a problem that after It Auto homes while displaying " HicBlue 1.1.4 " Z-axis will rise changing the display to " Endstops Z " or "G28 Z Forbidden"
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance " this is why Z-axis rises by design " to give be room for clearing the leaking filament.

attached is the Configuration.h
Configuration.h
(61.34 KiB) Downloaded 50 times
Attached is Configuration_adv.h
Configuration_adv.h
(56.66 KiB) Downloaded 44 times
They both print all functions seems to operate correctly
Both get a CRC when when using M500 using 461 bytes."do not know if 'CRC' was an added feature", only using 53% EEProm.
Last edited by Roberts_Clif on August 28th, 2017, 9:33 pm, edited 2 times in total.
Electronics Technician / Computer Programmer

Sometimes the correct answer if not essential to a solution.
If the information provided indirectly leads you to a solution.

User avatar
LePaul
Reactions:
Posts: 3108
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Marlin 1.1.4

Post by LePaul » August 27th, 2017, 6:20 pm

I wish I could help
I have 1.1.2 and changed the esteps and PID settings. I've uploaded and new changes aren't showing

User avatar
Roberts_Clif
Reactions:
Posts: 400
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: Marlin 1.1.4

Post by Roberts_Clif » August 28th, 2017, 7:10 am

LePaul wrote:
August 27th, 2017, 6:20 pm
I wish I could help
I have 1.1.2 and changed the esteps and PID settings. I've uploaded and new changes aren't showing
Does Marlin 1.1.2 Have the save features as 1.1.4.
Separate X, Y, and Z homes
Auto bed leveling in Menu
Light dimmer form Controller
Electronics Technician / Computer Programmer

Sometimes the correct answer if not essential to a solution.
If the information provided indirectly leads you to a solution.

User avatar
LePaul
Reactions:
Posts: 3108
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Marlin 1.1.4

Post by LePaul » August 28th, 2017, 8:28 am

Not sure about that

User avatar
Roberts_Clif
Reactions:
Posts: 400
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: Marlin 1.1.4

Post by Roberts_Clif » August 28th, 2017, 9:14 am

I have Changed Bed leveling from Linear to Bi-linear saving 6812bytes still CRC error but smaller number "-118."
Still " Endstops Z " on display.

Have dropped the Memory use below 50% Still CRC on M500.
Must be something to do with Endstop Z coding will look again!!!!!!!

I have determined the Exact line causing the Problem.

#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

I am using the above line with a PNP Proximity Sensor in place of the Z end-stop
switch, along with the following lines

#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 2 // Z Clearance between probe points

This allows me to home then raise Z-Axis 10mm for a clearance of 10.5mm " #define Z_PROBE_OFFSET_FROM_EXTRUDER -0.5 "
When I auto Home I get her errors " Endstops Z " or "G28 Z Forbidden "
Now when I use this line

#define Z_MIN_PROBE_ENDSTOP

I get no errors, though I can not get the Z-Axis to Raise.
Electronics Technician / Computer Programmer

Sometimes the correct answer if not essential to a solution.
If the information provided indirectly leads you to a solution.

Post Reply

Return to “Software and Firmware Discussion”

Who is online

Users browsing this forum: No registered users and 4 guests