Board layout question...

Have a suggestion for the forum? Requests? Please share
Post Reply
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Board layout question...

Post by LePaul »

On the home page, do you think I should move the general section down under, say, "Filaments"?

Maybe less scrolling for the busier posting areas? (Or leave things alone)
forum-layout.JPG
User avatar
Amedee
Reactions:
Posts: 599
Joined: February 15th, 2016, 11:10 am
Location: Brussels, Belgium
3D Printer(s): UMO / UMO+
Contact:

Re: Board layout question...

Post by Amedee »

No opinion -- I only use the 'Unread' page ;)
User avatar
Izzy
Reactions:
Posts: 604
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Board layout question...

Post by Izzy »

I usually go straight to unread posts, and then glance to see if there's something interesting, but alphabetically would be good
reibuehl
Reactions:
Posts: 506
Joined: February 9th, 2016, 9:56 am
Location: Stuttgart, Germany
3D Printer(s): Ultimaker 2

Re: Board layout question...

Post by reibuehl »

Same for me - the unread page is my starting point. I would only wish for the forum to kick me back to the unread page after pressing "mark all read" :)
User avatar
drayson
Reactions:
Posts: 254
Joined: February 15th, 2016, 5:04 am
Location: Graz, Austria
3D Printer(s): UMO with mods :-)

Re: Board layout question...

Post by drayson »

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
same to me... :-)
MTVDNA
Reactions:
Posts: 138
Joined: August 7th, 2016, 10:29 pm
Location: Netherlands
3D Printer(s): Ultimaker 2

Re: Board layout question...

Post by MTVDNA »

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
+1
User avatar
nilrog
Reactions:
Posts: 438
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Board layout question...

Post by nilrog »

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
Ditto! :)
User avatar
martin-bienz
Reactions:
Posts: 172
Joined: February 22nd, 2016, 2:42 am
Location: Switzerland
3D Printer(s): Ultimaker Original, prusa i3 mk2

Re: Board layout question...

Post by martin-bienz »

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
Youp, same here.
User avatar
ivan.akapulko
Reactions:
Posts: 389
Joined: February 11th, 2016, 11:27 am
Location: Ust-Kamenogorsk, Kazakhstan
3D Printer(s): Ultimaker 2
Contact:

Re: Board layout question...

Post by ivan.akapulko »

Agreed about Unread pages.
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Board layout question...

Post by LePaul »

Okay....again I will leave things alone! Thanks for your feedback
Post Reply

Return to “Feedback, suggestions and more”