Board layout question...

Have a suggestion for the forum? Requests? Please share
Post Reply
User avatar
LePaul
Reactions:
Posts: 2735
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5
Contact:

Board layout question...

Post by LePaul » October 26th, 2016, 2:04 pm

On the home page, do you think I should move the general section down under, say, "Filaments"?

Maybe less scrolling for the busier posting areas? (Or leave things alone)
forum-layout.JPG

User avatar
Amedee
Reactions:
Posts: 599
Joined: February 15th, 2016, 11:10 am
Location: Brussels, Belgium
3D Printer(s): UMO / UMO+
Contact:

Re: Board layout question...

Post by Amedee » October 26th, 2016, 2:44 pm

No opinion -- I only use the 'Unread' page ;)
Phil.

User avatar
Izzy
Reactions:
Posts: 589
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Board layout question...

Post by Izzy » October 26th, 2016, 3:00 pm

I usually go straight to unread posts, and then glance to see if there's something interesting, but alphabetically would be good
Izzy.

reibuehl
Reactions:
Posts: 410
Joined: February 9th, 2016, 9:56 am
Location: Stuttgart, Germany
3D Printer(s): Ultimaker 2

Re: Board layout question...

Post by reibuehl » October 26th, 2016, 4:55 pm

Same for me - the unread page is my starting point. I would only wish for the forum to kick me back to the unread page after pressing "mark all read" :)
Reiner.

User avatar
drayson
Reactions:
Posts: 235
Joined: February 15th, 2016, 5:04 am
Location: Graz, Austria
3D Printer(s): UMO with mods :-)

Re: Board layout question...

Post by drayson » October 27th, 2016, 2:22 am

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
same to me... :-)

User avatar
MTVDNA
Reactions:
Posts: 121
Joined: August 7th, 2016, 10:29 pm
Location: Netherlands
3D Printer(s): Ultimaker 2

Re: Board layout question...

Post by MTVDNA » October 27th, 2016, 2:52 am

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
+1

User avatar
nilrog
Reactions:
Posts: 380
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Board layout question...

Post by nilrog » October 27th, 2016, 3:11 am

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
Ditto! :)

User avatar
martin-bienz
Reactions:
Posts: 172
Joined: February 22nd, 2016, 2:42 am
Location: Switzerland
3D Printer(s): Ultimaker Original, prusa i3 mk2

Re: Board layout question...

Post by martin-bienz » October 27th, 2016, 4:35 am

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
Youp, same here.

User avatar
ivan.akapulko
Reactions:
Posts: 377
Joined: February 11th, 2016, 11:27 am
Location: Ust-Kamenogorsk, Kazakhstan
3D Printer(s): Ultimaker 2
Contact:

Re: Board layout question...

Post by ivan.akapulko » October 27th, 2016, 7:36 am

Agreed about Unread pages.

User avatar
LePaul
Reactions:
Posts: 2735
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5
Contact:

Re: Board layout question...

Post by LePaul » October 27th, 2016, 9:20 am

Okay....again I will leave things alone! Thanks for your feedback

Post Reply

Return to “Feedback, suggestions and more”

Who is online

Users browsing this forum: No registered users and 1 guest