Smaller nozzles

Show us your latest print!
Post Reply
User avatar
Izzy
Reactions:
Posts: 594
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Smaller nozzles

Post by Izzy » June 5th, 2017, 4:10 pm

I've been testing the smaller nozzles and have just finished my latest Braq dragon.
IMG_1177.JPG
The one at the back is the full size one printed with a 0.4mm nozzle in Faberdashery 'BlingBlingGold'
The cream one is printed at 50% with a 0.25mm nozzle in Faberdashery 'Glowbug yellow'.
And at the front the small one is printed at 35% with the 0.15mm nozzle in Faberdashery 'Orange Fizz' a slightly translucent filament. There is a standard nozzle in the front for scale as well.
Now I'm looking for a suitable filament to test the 0.1mm nozzle, at 25%.
Although I dont think it will be fully articulated, trying to get the elastic through those small holes in the parts was difficult enough in the 35% one, it was a bit like trying to get a worm back into its hole, trying to thread a very small wire though and get it to turn through a right angle and push through so that it could then be used to pull through the elastic was not the easiest.
The neck and tail were ok it was the wings and legs that were testing.
Izzy.

User avatar
Roberts_Clif
Reactions:
Posts: 236
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: Smaller nozzles

Post by Roberts_Clif » September 27th, 2017, 7:42 pm

Is there a website to download these models.

User avatar
jonnybischof
Reactions:
Posts: 276
Joined: February 15th, 2016, 2:48 am
Location: Zurich, Switzerland
3D Printer(s): UMO

Re: Smaller nozzles

Post by jonnybischof » October 4th, 2017, 3:34 am

Roberts_Clif wrote:
September 27th, 2017, 7:42 pm
Is there a website to download these models.
https://www.thingiverse.com/thing:854575

Google says there is ;)
Best regards,
Jonny

User avatar
LePaul
Reactions:
Posts: 2869
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Smaller nozzles

Post by LePaul » October 5th, 2017, 10:38 am

Yeah @Izzy has been kind of quiet on here!

User avatar
Izzy
Reactions:
Posts: 594
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Smaller nozzles

Post by Izzy » October 13th, 2017, 4:16 pm

Sorry guys, been busy as Sue lost her father in May and we have been going upto Warrington a lot and have the coroners court in November as he had a bad stroke to his brain stem.
I’ve not been using my small nozzles lately as Sue and I have been running a lot of PolySmooth, we have been testing it for some more finer and delicate prints, including making, cleaning, polishing and assembling six yes 6 Braq dragons at 75% scale 2 or each in Black, Teal and Transparent, 1 of each plus some other items will go back to 3DFilaPrint for there display as a thanks for the loan of the Polysher. But more of that along with our report when we have finished it all...
Izzy.

User avatar
Izzy
Reactions:
Posts: 594
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Smaller nozzles

Post by Izzy » October 13th, 2017, 4:16 pm

For the Braq Dragon just search Braq on Thingiverse.
Izzy.

User avatar
jonnybischof
Reactions:
Posts: 276
Joined: February 15th, 2016, 2:48 am
Location: Zurich, Switzerland
3D Printer(s): UMO

Re: Smaller nozzles

Post by jonnybischof » October 16th, 2017, 2:36 am

Sorry to hear that Izzy & Sue!
I hope you two are well under the circumstances.
Best regards,
Jonny

Post Reply

Return to “Show off your latest print”

Who is online

Users browsing this forum: No registered users and 3 guests