Tweaking the blobs out

Have a print that has problems? Need some feedback? Post it here.
User avatar
Neotko
Reactions:
Posts: 1142
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Tweaking the blobs out

Post by Neotko »

How many print hours since the last coupler was replaced?
User avatar
Titus
Reactions:
Posts: 252
Joined: February 9th, 2016, 10:20 pm
3D Printer(s): Ultimaker Original+HBK

Re: Tweaking the blobs out

Post by Titus »

In my case that was no problem, as the brass was touching the nozzle anyway
User avatar
Titus
Reactions:
Posts: 252
Joined: February 9th, 2016, 10:20 pm
3D Printer(s): Ultimaker Original+HBK

Re: Tweaking the blobs out

Post by Titus »

The only tinkering that might be required is the fanshroud. My old designed fan shroud was too large, the nozzle didn't clear the shroud as the Ruby is less high than the original UMO nozzle. Do you have a picture of your hot end? And as Neotko mentioned, your coupler?
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

I do, buried in the ruby nozzle test pilot's thread

So if the nozzle sits flush on the heater block, that's no big deal? I thought it was.

When I first mounted the nozzle post

Then installed
installed.jpg
I'll have to dig through the Shroud thread to see how it worked with the dual fan cap
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

Yes, it does fit. Found a few pics....I had used the ruby a lot for many prints and that shroud.
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

Finally a night to assemble a ruby nozzle and install it in the UMO. I had to raise the Z limit switch a half inch so the nozzle got close to the bed. (Forgot I had to do that last time too). The nozzle sticks out a good deal since the brass pipe is in so far but I heated , tightened and checked again. Everything seems flush

Here's that robot print with the ruby
IMG_4831.JPG
User avatar
Titus
Reactions:
Posts: 252
Joined: February 9th, 2016, 10:20 pm
3D Printer(s): Ultimaker Original+HBK

Re: Tweaking the blobs out

Post by Titus »

That looks a lot better or not? Strange right?
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

He looks a bit better, if you click on the image, there's still a few blobs by the left eye

This is using Ultimaker silver PLA, so it may desire a higher temp. I printed at 215C, which is what my Colorfabb materials like with the ruby nozzle.

Tonight I'll try it again at 225 and see what we get.
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

IMG_4845.JPG
This is at 225C
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

Here's 230C

I wonder if I should increase the fan a little?
IMG_4848.JPG
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

Still the same blobs. Hmm. Not sure what else to tweak on this. Maybe a bit more retraction? Using the latest Cura
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

Izzy wrote:Two questions, what layer height are you using?
The photos attached are at 0.1mm (100um) layer heights. 210'C Nozzle,50'C bed at 45mm/s.
0.2
Ruby nozzle 60C bed, 40 mm/sec
Looking at retraction it is 45 mm/sec and 4.8 distance, which I can increase

Did a few searches and Minimal Extrusion setting might be worth looking at
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

Just tried a little experiment

Ever tweak so much in Cura you suspect one of the zillion of settings is fouled up? Yeah...so went to 15.04.6 which has always worked fine. I don't dare touch 2.3.1 since I have nGen setup darn-near-perfect for the Ultimaker 2+ (I really wish I could saving settings and name it 'nGen' and make something similar for Colorfab PLA, for Ultimaker PLA, etc.)

With that said, I did the robot with the same basic settings... 0.2 layers, 225C , bed at 60C, retraction at 45 mm/sec and 4.6mm distance....and it came out very nice! I decided to do a different print, this time the 2 owls one. Again, same settings but a tad more fan since we still have a little droop in the Ultimaker robot's chest. 3 hours to go!
User avatar
LePaul
Reactions:
Posts: 3966
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): 24 - Yes I have a problem!
Contact:

Re: Tweaking the blobs out

Post by LePaul »

A few little blobs here and there but overall a really nice print
IMG_4850.JPG
User avatar
Izzy
Reactions:
Posts: 604
Joined: February 12th, 2016, 2:29 am
Location: England
3D Printer(s): Ultimaker 2

Re: Tweaking the blobs out

Post by Izzy »

Re saving your profiles,
you can with S3D ;-) and I thought you could with Cura too, I haven't used it for a few months now but I'm sure you could save profiles.
Post Reply

Return to “Help me fix this print!”