Tweak this?

Discussion about Simplify 3D software
User avatar
Neotko
Reactions:
Posts: 1141
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Tweak this?

Post by Neotko » March 26th, 2017, 3:22 am

The infill overlap is a bit too high.

What orange spot?

User avatar
LePaul
Reactions:
Posts: 2916
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Tweak this?

Post by LePaul » March 26th, 2017, 9:09 am

In the previews

User avatar
Neotko
Reactions:
Posts: 1141
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Tweak this?

Post by Neotko » March 26th, 2017, 11:23 am

The legend says is 'infill' and by the looks it seems infill from layers below. Try to inspect the gcode for that kind of things layer by layer. There's a button to see just current layer selected on the slider.

User avatar
LePaul
Reactions:
Posts: 2916
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Tweak this?

Post by LePaul » March 26th, 2017, 6:10 pm

Neotko wrote:The infill overlap is a bit too high.

What orange spot?
Do you mean the Outline Overlap, in the Infill tab?

User avatar
Neotko
Reactions:
Posts: 1141
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Tweak this?

Post by Neotko » March 26th, 2017, 6:31 pm

Yea

User avatar
LePaul
Reactions:
Posts: 2916
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Tweak this?

Post by LePaul » March 26th, 2017, 6:33 pm

Been reading this...

https://forum.simplify3d.com/viewtopic.php?t=1953

Going to lower to 27% and do a test print That finish could be better

User avatar
Neotko
Reactions:
Posts: 1141
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Tweak this?

Post by Neotko » March 26th, 2017, 6:38 pm

Indeed. As I said the 3 thinks at the same time... :D

Also yea 25 is more than ok for almost anything.

User avatar
LePaul
Reactions:
Posts: 2916
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Tweak this?

Post by LePaul » March 26th, 2017, 8:38 pm

Tried a different small part

Back, with 25%. Right with 20%

Left is Cura default
IMG_6439.JPG

User avatar
LePaul
Reactions:
Posts: 2916
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Tweak this?

Post by LePaul » March 28th, 2017, 10:10 am

If you click the photo and zoom in, note the S3D pieces (back and right)....note the sides of the part, especially where the hole mounts are

Post Reply

Return to “Simplify 3D”

Who is online

Users browsing this forum: No registered users and 1 guest