Let's speculate...
- LePaul
- Reactions:
- Posts: 3966
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Let's speculate...
...since it is a quiet summer day...
When do you think we'll see the next version of the Ultimaker?
Will it have a bigger build volume?
Other features?
When do you think we'll see the next version of the Ultimaker?
Will it have a bigger build volume?
Other features?
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: Let's speculate...
2 weeks?
- LePaul
- Reactions:
- Posts: 3966
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Let's speculate...
Ah that's a popular answer
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: Let's speculate...
Ok week and a half
- LePaul
- Reactions:
- Posts: 3966
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Let's speculate...
I'm hoping something larger in volume
My projects I'd like to print need bigger volume (wider and taller than Extended)
My projects I'd like to print need bigger volume (wider and taller than Extended)
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: Let's speculate...
It's quite expensive to go wider than just going taller, so both probably will cost quite a bit of money.
- Izzy
- Reactions:
- Posts: 604
- Joined: February 12th, 2016, 2:29 am
- Location: England
- 3D Printer(s): Ultimaker 2
Re: Let's speculate...
I was wondering about a wider print area, I had a job on my hub that would have required the component being printed at a vertical and plain diagonal, which more than doubled the material due to supports.
At my wife's surgestion I looked for a printer with a larger print area, but when I looked at ones below £800 I didn't find one, although they are physically larger than the UM there print volume is smaller.
So perhaps a UM2 Wide, with a 450x225 print bed.
Oh and a laser cutter attachment.
At my wife's surgestion I looked for a printer with a larger print area, but when I looked at ones below £800 I didn't find one, although they are physically larger than the UM there print volume is smaller.
So perhaps a UM2 Wide, with a 450x225 print bed.
Oh and a laser cutter attachment.
- Izzy
- Reactions:
- Posts: 604
- Joined: February 12th, 2016, 2:29 am
- Location: England
- 3D Printer(s): Ultimaker 2
Re: Let's speculate...
Who's a hoopy frude, where's you towel?
And I'm supprised at you, Belg**m is the worst sware word in the known Galaxy!
And I'm supprised at you, Belg**m is the worst sware word in the known Galaxy!
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: Let's speculate...
And thanks for all the fish!
- LePaul
- Reactions:
- Posts: 3966
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Let's speculate...
Well I know a few friends have bought, or have on order, the Raise3D N2 Plus
12 x 12 x 24 (inches)
304.8 x 304.8 x 609.6 (mm)
12 x 12 x 24 (inches)
304.8 x 304.8 x 609.6 (mm)
- Dim3nsioneer
- Reactions:
- Posts: 221
- Joined: February 19th, 2016, 2:13 pm
- Location: Zurich Area, Switzerland
- 3D Printer(s): Ultimaker Original, 2, 2+, 2 Ext+, 3, S5, Form 2
- Contact:
Re: Let's speculate...
1 week.
And it will have the geared feeder of the UM2+, rather more than one of them. Bundled with Cura2.2.
And it will have the geared feeder of the UM2+, rather more than one of them. Bundled with Cura2.2.
- drayson
- Reactions:
- Posts: 254
- Joined: February 15th, 2016, 5:04 am
- Location: Graz, Austria
- 3D Printer(s): UMO with mods :-)
Re: Let's speculate...
1 week???
not so soon please - there I'll be on vacation...
not so soon please - there I'll be on vacation...
- Meduza
- Reactions:
- Posts: 289
- Joined: February 10th, 2016, 8:08 pm
- Location: Stockholm, Sweden
- 3D Printer(s): UM2+, UM3 (F2, UM2EX+ UM3EX, etc at work)
- Contact:
Re: Let's speculate...
I believe we will se the next version when it is released
- Dim3nsioneer
- Reactions:
- Posts: 221
- Joined: February 19th, 2016, 2:13 pm
- Location: Zurich Area, Switzerland
- 3D Printer(s): Ultimaker Original, 2, 2+, 2 Ext+, 3, S5, Form 2
- Contact:
Re: Let's speculate...
This seems obvious but it's most probably not true. If Ultimaker follows its style for announcements, we will get a picture of the new device in the almost dark first. So we will not see it when it is (going to be) released...Meduza wrote:I believe we will se the next version when it is released