3D Printing Forum

This is what I get when I set my filament size to 3mm when using 1.75mm filament.

Sample printed image

Isn't that part of the raft that needs to be removed.

Post a larger image so we can see it better

BOTH configuration.h, configuration_adv.h are needed though configuration_adv.h have a lot of options that in simple mode work with default. Most popular 3D Printers have a starting Marlin configuration.h that will supervise until you learn to configure you own custom config. What 3D Printer are you...

I had this problem on my Hictop, as i believe that the display cables were too long. Solved the problem by shielding the cables leading to the Display and created a 3D Printed shielded controller cover. I used Aluminum Foil Tape to line the 3D Printed case and connected a ground wire to the foil at ...

I created a controller case with fan shown in this link

Well looked for STL filse could not find reposted
Attaching here base and Cover

I built this simple Enclosure pictured below and believed that my 3DP11 and 3DP12 print ABS almost to perfection. The Twins 2.jpg I 3D Printed in ABS most of the Parts for my MPCNC My MPCNC.jpg carriage.jpg Though I had problems with bed warping at temps above 96C I never had problems printing any m...

I should have noted that not all Hictop 3D Printers have the 220 X 270 Bed surface.

In Cura Click on Preferences select Printers
Select Machine Settings.
You will see the settings used in my Hictop 3D Printers

Below is the code line you want.

I forgot one cause If the power supply wires are not large enough to carry the current. This may not apply on Ender's though did have a bearing on supply voltage on my Hictop's. The Supply voltage could be correct on power supply though could be below specs on controller board. This could mean large...

There are many reasons for layer shifting. Without the printers settings it will be hard to diagnoses, Layers shifting could be caused by print speed, dirty bearings, configurations settings or debris on smooth rods . I had to clean my bearings an smooth rods thoroughly before I could get smooth pri...

I have upgraded thru 10 different Marlin 2 versions scene making my first Marlin 2 leap with my 4 Hictop 3DP 3D Printers. An have assisted 14 different users upgrade their Hictop printers into version 2's of Marlin with great success. An all this was done because of Chip Luck post of an old version ...

I have many Marlin 2 version firmware that are configured for stock hardware 3DP11 and 3DP12 Hictops. Only meant to refer that the next version gave me troubles. A note that in every version of Marlin there could be a bug , thous the reason for Bug Fixes. Sorry Have to go emergency, will get back to...

I have upgraded my 3DP11 to the best Hictop an have made the same modification to my 3DP12s. If you were to just read this Thread in this forum about Hictop style 3D printers your Hictop would quickly be your best 3D Printer. I have found all the best 3DP upgrades an modified all my 3D Printers, to ...

I trust my Hictop 3DP11 the older 12Volt version of the Newer 3DP12 24volt 3D Printer. In my case the 3DP11 is called Red, my 24volt 3DP12's are Blu and Pur My first flash was from Chip Luck is located here. Though have never changed the firmware after posting and confirmed working of my google driv...

I trust my older 3DP11 12 volt 3D Printer though the newer version 3DP12 a 24 volt 3D Printer work just as good. My 3DP11 is called Red while Blu and Pur are my newer 24 volt 3D Printers. Have not determined the name will be calling my Hictop 3DP12 CoreXY but will decide one day before I finish buil...