Search found 137 matches

by MTVDNA
October 27th, 2016, 6:32 pm
Forum: General Discussion
Topic: A Tea between friends :-) How was Your Day
Replies: 1460
Views: 158146

Re: A Tea between friends :-) How was Your Day

Those are some cute kitties. I'm more of a dog person myself though.
by MTVDNA
October 27th, 2016, 6:29 pm
Forum: General Questions
Topic: Help with a lifting brim, please!
Replies: 10
Views: 2594

Re: Help with a lifting brim, please!

I've never used tape so I can't help you with that. Clean glass at 60 °C works just fine for me when I'm using PLA. I only use a brim when I print something with sharp corners, round edges don't tend to warp as much usually. I did have some issues with poor first layer adhesion, even though the bed ...
by MTVDNA
October 27th, 2016, 2:52 am
Forum: Feedback, suggestions and more
Topic: Board layout question...
Replies: 9
Views: 2254

Re: Board layout question...

Amedee wrote:No opinion -- I only use the 'Unread' page ;)
+1
by MTVDNA
October 26th, 2016, 10:56 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: Upgraded Ultimaker 2 to 2+...what's this noise?
Replies: 11
Views: 2034

Re: Upgraded Ultimaker 2 to 2+...what's this noise?

Sounds like you should upgrade to dual extrusion by using foehnsturm's tool changing system! :P
by MTVDNA
October 26th, 2016, 9:54 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: Upgraded Ultimaker 2 to 2+...what's this noise?
Replies: 11
Views: 2034

Re: Upgraded Ultimaker 2 to 2+...what's this noise?

Do you mean the "beep beep"? That's just the feeder retracting. Just look at the back, you can see the stepper moving ;)
by MTVDNA
October 24th, 2016, 2:23 pm
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

By feedrate I assume you mean speed? I agree this is a good way to test what speed you can reach, but what I like about the cylinders is that you get an easily reproducible result that you can compare to others. In my experience so far, you do indeed need to increase the flow rate when you print fas...
by MTVDNA
October 24th, 2016, 12:05 am
Forum: General Discussion
Topic: A Tea between friends :-) How was Your Day
Replies: 1460
Views: 158146

Re: A Tea between friends :-) How was Your Day

Capital and lower case letters, numbers, symbols, and plenty of characters. You taught your kid well! :P
by MTVDNA
October 23rd, 2016, 10:50 am
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

Could you point me to those better tests? I'm very curious to try them!
by MTVDNA
October 23rd, 2016, 9:43 am
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

Ah yes, you are right about that. On the small cylinders the text is much crisper at lower speed. On the big cylinder the text seems to be printed at the same speed every time, so the quality doesn't really change.
by MTVDNA
October 22nd, 2016, 6:23 pm
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

Ivan, I don't really understand you. What image are you referring to, and what do you mean by shifting axis?
by MTVDNA
October 22nd, 2016, 3:26 pm
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

I've never tried timing the test, and I'm not sure how useful it would be since it prints the text quite a bit slower than the rest of the cylinder. I could try printing a simple cylinder without text and see how it turns out. Might be interesting... A square is a little bit trickier than a circle, ...
by MTVDNA
October 22nd, 2016, 2:59 pm
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

Of course! The best way to learn is to share experiences if you ask me. You take some and you give some. What I forgot to add above by the way: Printing PLA at 230 °C is not a very representative test if you ask me. That is not a temperature you would use when actually printing something. Overhangs ...
by MTVDNA
October 22nd, 2016, 2:04 pm
Forum: General Discussion
Topic: The Flex3Drive
Replies: 37
Views: 5325

Re: The Flex3Drive

Hey guys, I had some time today so I wanted to show you some tests I did on my printer. Of course one of the most interesting things to test is the extrusion: how fast can you go? I printed a bunch of test cylinders, both with the UM2 with Robert's feeder modification , and with the Flex3Drive. I go...
by MTVDNA
October 19th, 2016, 3:55 pm
Forum: General Discussion
Topic: Ultimaker 3 reveal trip
Replies: 20
Views: 2865

Re: Ultimaker 3 reveal trip

Looks like you guys had a good time!
by MTVDNA
October 19th, 2016, 5:59 am
Forum: General Discussion
Topic: Teaser for the New Ultimaker....here we go!
Replies: 140
Views: 12544

Re: Teaser for the New Ultimaker....here we go!

Could you tell us something about the feeder? It looks different from the UM2+ feeder (much thicker), but what has changed?

Edit:
I'd also like to see some video that was taken using the built in camera. The timelapses that are shown don't appear to be made by it, the camera angle doesn't match.

Go to advanced search