3D Printing Forum

Here are my Cura settings for 2.6.2 they are importable to 3.2.1

Izzy: you are looking for HI-TEMP HI-FORCE 44™ SOLDER, though it cost $15 for a single ounce. When you solder with HI-TEMP 44 Solder it need to be done as quickly as possible as the traces will separate from the board material from overheating. ( more commonly called Silver Solder) Contains 95% Cadm...

Thank you, It look's as though your code is correct. You could try to the Enable the Disable individual pull-up for Your Proximity may not like the pull-up resistor. #define ENDSTOPPULLUP_ZMIN #define ENDSTOPPULLUP_ZMIN_PROBE Have you measured the voltage level output from the proximity sensor. (Bet...

Looking at you configuration file custom name is limited to 13 characters for MLCD2004 Displays or they will cause the top line to display incorrectly. #define CUSTOM_MACHINE_NAME "DKDGWi HICTOP 3DPDK" // DKDGWi As you have not provided us with your Proximity sensor make or model, will exp...

Have you taken any measurement from the Z-Axis connector to see it any of the pins are open or shorted. Image2.jpg I found one of my controllers had a open trace (shown above), I soldered the broken trace Do you have a configuration.h file you can show us. Would take a look if you have one. (I have ...

I have upgraded to Marlin 1.1.5 though I start all print between 32-46 speed and print between 60-80. As the different software may print at different speeds linked is a video on you-tube I use this fix as the bottom of the smooth rods are not supported well. Print these smooth rod brackets. Downloa...

I have added heat sink to the Mosfet I a single aluminum bar with insulators across all, and a fan to keep the components cool. IMG_1682.JPG I added heat sinks to all the stepper drivers and set the stepper current to .695 on all except Z-Axis 1.396 on my 12 volt Printer and set the stepper current ...

Hello Adrian_S Hictop 3DP11 Aluminum has some small problems and I have posted my fixes on this forum. One being the all thread Z-Axis lead screws, moving too an fro. When I first assembled my 3DP11 found that if you wrap a single layer of electrician tape on the bottom of the Z-Axis lead screws it ...

The only thing I can thing of that could cause this is if you accidentally changed the Filament diameter from 1.75 to 3.0mm (Have done this myself).
That will cause under-extrusion or even a clogged nozzle.

I will add the Reel to Reel, 9-track NRZI Storage drives, 5 1/4" and 8" floppy disks. Centronis 779 line printer with a variable control to chance charters per line. For those of you who did not have one. The Centronics 779 line printer on the back Had a (adjustable "let's say volume ...

I believe that Marlin 15.04.6 uses Pronterface UI but do not quote me.

I know that on occasion when re-flashing sometimes the EEProm are not cleared of data that can cause the new firmware to act strangely. If you have enabled EEPROM in configuration.h I clear errors by sending M502 (Factory Reset) and a M500 (Store Settings) or more simply stated a factory reset and t...

I have a 3DP12 running Marlin 1.1.5 and on many occasions have installed my backup controller, after flashing a new firmware to test it's functionality. All the Stepper cables are all keyed so they cannot be plugged in backwards. Did you upgrade to a newer version of Marlin and re-flashed the firmwa...

Log File is in a hidden directory
C:\Users\"User Login ID"\AppData\Local\cura

I have successfully install Cura 15.04.6 and Cura 3.2.1 with no problems. Checking the system requirements Intel Core 2 or AMD Athlon 64 or newer Windows Vista or higher, 64 bit. 32 Bit not supported after Cura 2.3. OpenGL 2 compatible graphics chip, OpenGL 4.1 for 3D Layer view. https://ultimaker.c...