Search found 456 matches

by reibuehl
June 12th, 2017, 4:12 pm
Forum: News and Announcements
Topic: We Upgraded!
Replies: 21
Views: 2339

Re: We Upgraded!

Many thanks @LePaul! Looks much better now at 100%.
by reibuehl
June 12th, 2017, 9:32 am
Forum: News and Announcements
Topic: We Upgraded!
Replies: 21
Views: 2339

Re: We Upgraded!

by reibuehl
June 12th, 2017, 9:30 am
Forum: News and Announcements
Topic: We Upgraded!
Replies: 21
Views: 2339

Re: We Upgraded!

The problem with the browser zoom is that it enlarges everything. By the time the font is in a comfortable size, the rest of the page looks very awkward since the graphics get scaled too and they seem too large then.
by reibuehl
June 12th, 2017, 3:10 am
Forum: News and Announcements
Topic: We Upgraded!
Replies: 21
Views: 2339

Re: We Upgraded!

Thanks for confirming @nilrog! Good to know that I am ONLY far sighted and not also senile :-D
by reibuehl
June 11th, 2017, 7:59 am
Forum: News and Announcements
Topic: We Upgraded!
Replies: 21
Views: 2339

Re: We Upgraded!

Has the font size changed or did we have a "old guy with bad eyes" setting that I had selected and that is now gone? Even at 120% magnification in the browser every font looks smaller than before the upgrade...
by reibuehl
June 11th, 2017, 7:53 am
Forum: General Discussion
Topic: A Tea between friends :-) How was Your Day
Replies: 1449
Views: 137770

Re: A Tea between friends :-) How was Your Day

The font is definitely smaller for me not bigger.
by reibuehl
May 31st, 2017, 7:55 am
Forum: General Discussion
Topic: Interesting Ultimaker Steel Frame Build
Replies: 25
Views: 3219

Re: Interesting Ultimaker Steel Frame Build

I asked Stahlwerk and they say it will draw max 16 amps but as Meduza says, that is only if you use the full 200 amps welding current.
by reibuehl
May 30th, 2017, 7:00 am
Forum: General Discussion
Topic: Interesting Ultimaker Steel Frame Build
Replies: 25
Views: 3219

Re: Interesting Ultimaker Steel Frame Build

The Stahlwerk welder that @Meduza mentioned is sold in Switzerland, maybe they can tell you what plug they use.
by reibuehl
May 30th, 2017, 5:28 am
Forum: General Discussion
Topic: Interesting Ultimaker Steel Frame Build
Replies: 25
Views: 3219

Re: Interesting Ultimaker Steel Frame Build

Since it is "only" 230V, I would think that it needs somewhere between 10-16A, maybe even less. I currently only have a very old stick welder and that one has welding currents up to 120A I think and works fine on a regular outlet with a 10A fuse.
by reibuehl
May 21st, 2017, 3:10 pm
Forum: Speciality and Experimental Filaments
Topic: Any experience with eSUN Cleaning Filament?
Replies: 4
Views: 853

Re: Any experience with eSUN Cleaning Filament?

When driving it trough, do you just put a piece in the bowden and then push with a regular filament? Or do you need to fuse it to some filament and then enter it normally through the feeder?
by reibuehl
May 21st, 2017, 8:00 am
Forum: Speciality and Experimental Filaments
Topic: Any experience with eSUN Cleaning Filament?
Replies: 4
Views: 853

Any experience with eSUN Cleaning Filament?

Hi all,

has anybody of you used the eSUN Cleaning Filament? I have gotten some but have no idea how to use it really in the UM2.
by reibuehl
May 12th, 2017, 5:21 pm
Forum: Ultimaker 3 / Ultimaker 3 Extended
Topic: NFC scan plug port
Replies: 17
Views: 2046

Re: NFC scan plug port

LePaul wrote:Apparently these can come out alignment in shipping, I just hadn't seen any posts where this has happened to anyone other than me (big surprise, right?)
Do I need to say anything here? :-D
by reibuehl
May 12th, 2017, 3:56 am
Forum: Ultimaker 3 / Ultimaker 3 Extended
Topic: NFC scan plug port
Replies: 17
Views: 2046

Re: NFC scan plug port

I don't have an UM3, but isn't that just a remove the cover, loosen the mainboard and push it a little in the right direction and fasten it again job? Normally these screws have a little bit of slag and if the cover is moved to the lower end of that and the board to the upper end of that slag for ex...
by reibuehl
May 9th, 2017, 1:39 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: Block v3 or Olsson Block
Replies: 18
Views: 3842

Re: Block v3 or Olsson Block

So, you are basically doing Atomic Pulls on a regular basis - great idea! I can try this on my stock-feeder, because I have designed and fitted a release-lever to it, which was very easy to do - particularly when I moved it to the side of the machine. Would you be willing to share that release-leve...
by reibuehl
May 8th, 2017, 5:10 am
Forum: Simplify 3D
Topic: Support Advanced settings
Replies: 9
Views: 1145

Re: Support Advanced settings

The MODIFI3D looks nice but overpriced. I wonder if they only sell the tips and for what price? The device itself is identical to the standard 8W USB soldering iron sold at Ebay for under 5 EUR.

Go to advanced search