Search found 3488 matches

by LePaul
April 21st, 2020, 8:07 pm
Forum: Hardware Modifications
Topic: V6 Airbrush Nozzle
Replies: 5
Views: 1220

Re: V6 Airbrush Nozzle

Nope...I glanced :)
by LePaul
April 21st, 2020, 8:05 pm
Forum: General Discussion
Topic: Cannot Believe EveryOne is on Stay At Home Orders
Replies: 6
Views: 999

Re: Cannot Believe EveryOne is on Stay At Home Orders

I'm working from home and then every few hours, changing out 5 printers for their next load of ear savers for COVID

I wish I knew how to drive more people into the forums I include the link in all my YouTube videos!
by LePaul
April 17th, 2020, 11:31 am
Forum: Creality Large Scale 3D Printers
Topic: Bondtech Direct Drive System for the CR-10S
Replies: 0
Views: 1539

Bondtech Direct Drive System for the CR-10S

I was skeptical.... it's $260 But after messing with a few different E3Dv6/BMG combos that had me concerned about longevity (heat) and messing with the firmware...this thing is a huge time saver! And my CR-10S is cranking non stop and giving amazing results.

by LePaul
April 6th, 2020, 12:25 pm
Forum: General / RepRap Printers
Topic: Buying 3D printer
Replies: 5
Views: 1527

Re: Buying 3D printer

Those are all cheap Chinese printers. My experience with Geeetech has been they have absolutely zero quality control. From what I received, I am doubtful they powered it on after building it. Otherwise many obvious issues would have been noticed. I have Creality CR-10 and Creality CR-10S. Both have ...
by LePaul
April 2nd, 2020, 9:29 am
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: Cleaning the Z axis threads?
Replies: 3
Views: 1072

Re: Cleaning the Z axis threads?

My Ultimaker 2, upgraded to a 2+, has a pretty dark looking lead screw...Roberts advice is good.
by LePaul
April 1st, 2020, 11:07 am
Forum: General Discussion
Topic: COVID...stay healthy
Replies: 15
Views: 3681

Re: COVID...stay healthy

Hope everyone is staying healthy!
I have my FT-6 apart to install the E3D Hemera. Been doing a lot of prints on my Ultmaker 2+ and FT-5 How's everyone doing?
by LePaul
March 24th, 2020, 7:54 pm
Forum: General Discussion
Topic: COVID...stay healthy
Replies: 15
Views: 3681

Re: COVID...stay healthy

It's kinda like the movie Independence Day...minus the invading aliens!
by LePaul
March 22nd, 2020, 2:28 pm
Forum: Cura
Topic: 2nd Post - Understanding Supports in Cura
Replies: 5
Views: 5525

Re: 2nd Post - Understanding Supports in Cura

If @nallath isn't too busy maybe he can chime in?
by LePaul
March 22nd, 2020, 2:27 pm
Forum: Electronics
Topic: Bad power supply. I think.
Replies: 6
Views: 7821

Re: Bad power supply. I think.

A quick Google search brought up this
by LePaul
March 22nd, 2020, 2:25 pm
Forum: General Discussion
Topic: COVID...stay healthy
Replies: 15
Views: 3681

Re: COVID...stay healthy

I've been reading how hard Italy has been hit with Spain not far behind. Stay healthy!
by LePaul
March 22nd, 2020, 12:30 pm
Forum: General 3D Printing Conversation
Topic: Thingiverse going the Ultimaker route - downhill :-(
Replies: 2
Views: 1367

Re: Thingiverse going the Ultimaker route - downhill :-(

Yeah they made a change to their website recently and I don't know if that added to their woes.

Meanwhile MyMiniFactory works fine!
by LePaul
March 19th, 2020, 12:42 pm
Forum: General Discussion
Topic: COVID...stay healthy
Replies: 15
Views: 3681

COVID...stay healthy

I've been working from home for a week, since I traveled West where there were infections.

But so far, I am fine

And getting a lot of 3D printing done :-)
by LePaul
February 19th, 2020, 7:21 pm
Forum: Cura
Topic: Why is not Slicing?
Replies: 3
Views: 5711

Re: Why is not Slicing?

Check the Layer view and go layer by layer...i suspect the brim is hiding it?
by LePaul
February 18th, 2020, 1:29 pm
Forum: Cura
Topic: 1st Post - Understanding relationships in Cura
Replies: 4
Views: 3459

Re: 1st Post - Understanding relationships in Cura

I'm working to master Cura better since I have just setup two Ultimaker S5's at work

Here's a marvelous resource from Ultimaker

https://ultimaker.com/en/resources/21932-mastering-cura
by LePaul
February 5th, 2020, 9:51 pm
Forum: Cura
Topic: Doubling or Tripling up on inner layers?
Replies: 4
Views: 3398

Re: Doubling or Tripling up on inner layers?

I'm not sure I follow what you're asking for...but intrigued

Go to advanced search