Search found 1099 matches

by Roberts_Clif
September 24th, 2020, 8:22 pm
Forum: Creality Large Scale 3D Printers
Topic: MAXTEMP BED Error
Replies: 8
Views: 6286

Re: MAXTEMP BED Error

You have come to the right Forum, we ma quite a few users the have Creality 3D Printers.

When you have a question post your thread we will do our best to help you.

P.S. Welcome to 3D Printing Forum
by Roberts_Clif
September 21st, 2020, 7:17 am
Forum: Hardware Modifications
Topic: Repair or replace clogged nozzle?
Replies: 13
Views: 3961

Re: Repair or replace clogged nozzle?

Loosen the hex screw, insert the thermister into smaller hole route the wires one each side of the set screw and snug set screw.

The thermister should be bottomed out in the small hole, while the set screw holds the thernister wires as to not allow the thernister movement.
by Roberts_Clif
September 18th, 2020, 7:59 am
Forum: Cura
Topic: Model will slice but won't print
Replies: 2
Views: 1219

Re: Model will slice but won't print

It would be helpful to post your Cura Settings

Or you could examine my Cura Settings posted here

In some cases we need the Model to be able to do testing, to see what special setting may be required.
OR
Maybe the model has flaws an is in need of repair.
by Roberts_Clif
September 16th, 2020, 3:17 pm
Forum: General Discussion
Topic: Coffee Chat 2020
Replies: 2
Views: 2120

Re: Coffee Chat 2020

Getting Ready for my Halloween trick or treat prints.

They say School starts Oct 1 here. so Halloween should be a GO!!!!!
by Roberts_Clif
September 16th, 2020, 3:15 pm
Forum: General Questions
Topic: 3D Touch for Hictop
Replies: 10
Views: 2052

Re: 3D Touch for Hictop

PM them to me Please
by Roberts_Clif
September 15th, 2020, 10:44 am
Forum: General Questions
Topic: Hictop 3dp-12 help
Replies: 38
Views: 6694

Re: Hictop 3dp-12 help

This is a remake of my re-design
I have posted the information Here

More on this subject below
Fan Duct

I have not ideal where I got the heat-sink fins

Found some here you could cut to make half round
by Roberts_Clif
September 15th, 2020, 8:42 am
Forum: General Questions
Topic: 3D Touch for Hictop
Replies: 10
Views: 2052

Re: 3D Touch for Hictop

Thank You> LePaul Problem I have already purchased the 3D Touch, I somehow got it confused with the BL Touch. Thought I had purchased the BL Touch, As this is one of the problems with searches on E-Bay, They allow other similar merchandise to enter into your search results. It is OK though! I will m...
by Roberts_Clif
September 14th, 2020, 8:14 pm
Forum: General Questions
Topic: 3D Touch for Hictop
Replies: 10
Views: 2052

Re: 3D Touch for Hictop

Today the 3D Touch showed up, quickly opened to take a quick look see what my money had purchased. It looks pretty good, came with packaged like a Cadillac mounting a pair of screws four 3 pin, two 2 pin housings and pins plus male pins for extending the wire harnesses. It was at this time I decided...
by Roberts_Clif
September 10th, 2020, 10:26 am
Forum: General Questions
Topic: 3D Touch for Hictop
Replies: 10
Views: 2052

Re: 3D Touch for Hictop

Ordered a single unit will test to see if my pins are correct. Using my MPCNC with an Arduino Mega and Ramps 1.6
by Roberts_Clif
September 8th, 2020, 5:33 pm
Forum: General Questions
Topic: 3D Touch for Hictop
Replies: 10
Views: 2052

Re: 3D Touch for Hictop

3-pin: Brown (-, GND), Red (+5V), Orange (control signal) (Z-Max) 2-pin: Black (-, GND), White (Z min) 3D Touch.jpg Making sure the pin configuration is correct. Connect the 3 pin wire to the Z max pin. Connect the 2 pin wire to the Z min pin. Marlin Code Changes #define NUM_SERVOS 1 // Servo index...
by Roberts_Clif
September 8th, 2020, 9:39 am
Forum: General Questions
Topic: 3D Touch for Hictop
Replies: 10
Views: 2052

3D Touch for Hictop

3-pin: Brown (-, GND), Red (+5V), Orange (control signal) (Z-Max) 2-pin: Black (-, GND), White (Z min) 3D Touch.jpg Making sure the pin configuration is correct. Connect the 3 pin wire to the Z max pin. Connect the 2 pin wire to the Z min pin. Marlin Code Changes #define NUM_SERVOS 1 // Servo index ...
by Roberts_Clif
September 6th, 2020, 1:34 pm
Forum: General Questions
Topic: Hictop 3dp-12 help
Replies: 38
Views: 6694

Re: Hictop 3dp-12 help

This thread has a lot of good information
viewtopic.php?p=13993#p13993
by Roberts_Clif
September 6th, 2020, 12:43 pm
Forum: General Questions
Topic: Hictop 3dp-12 help
Replies: 38
Views: 6694

Re: Hictop 3dp-12 help

I am glad you are back to printing using Marlin 1.1.9BF. You made a few changes to 1.1.9BF post them for me would like to keep records for the next Hictop 3D Printer user that needs help. Note: I had several different version of Arduino IDE on my computer until my window 10 auto update crashed me. N...
by Roberts_Clif
September 5th, 2020, 11:25 am
Forum: General Questions
Topic: Hictop 3dp-12 help
Replies: 38
Views: 6694

Re: Hictop 3dp-12 help

Hictop models to 3D Print to get better models. Hic tech 3DP11 Z axis solid rod fix Help remove Z-Axis waves Hic Top Z-Axis Smooth Rod Support2.jpg HICTOP LCD on the bottom When my LCD was on Top EFI noise stopped prints in middle. Hictop Y Motor End stop Models help for a quicker y Axis setup ("Mod...
by Roberts_Clif
September 4th, 2020, 8:35 am
Forum: Firmware
Topic: Marlin 2.0.6
Replies: 3
Views: 1926

Re: Marlin 2.0.6

Over my 3D Printer ownership have been changing lines in pins_RAMPS.h Some I believe are still necessary though other can be moved to Configuration.h this set of lines for example #ifndef MOSFET_D_PIN #define MOSFET_D_PIN -1 #endif changing them to enable E1 or Fan1 PIN could stay in pins_RAMPS.h #i...

Go to advanced search