Search found 589 matches

by Izzy
August 26th, 2017, 4:33 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: Suddenly getting hairy stringy prints
Replies: 8
Views: 173

Re: Suddenly getting hairy stringy prints

My print shown is the hip of the Braq dragon, in Polymaker's PolySmooth, I'm about to test some retraction and fan settings for this material, there's stringy and hairy but this is ridiculous.
by Izzy
August 24th, 2017, 4:32 pm
Forum: General Discussion
Topic: A Tea between friends :-) How was Your Day
Replies: 1204
Views: 58891

Re: A Tea between friends :-) How was Your Day

I think Molly wants her own hamster ball
by Izzy
August 24th, 2017, 4:27 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: Suddenly getting hairy stringy prints
Replies: 8
Views: 173

Re: Suddenly getting hairy stringy prints

Did your hairy print resemble this one :-?
FullSizeRender.jpg
by Izzy
August 6th, 2017, 3:40 pm
Forum: General Discussion
Topic: A Tea between friends :-) How was Your Day
Replies: 1204
Views: 58891

Re: A Tea between friends :-) How was Your Day

It's a pity you can't fit him with a taser or pepper spray to get them back, perhaps a capacitor discharge on a flexible PCB track.
by Izzy
August 5th, 2017, 4:18 am
Forum: Feedback, suggestions and more
Topic: Lost posts
Replies: 22
Views: 877

Re: Lost posts

:-) it's a language barrier problem, some things including humour don't translate correctly, it can be tricky between English and Dutch, but English and American is a whole new can of worms :lol:
by Izzy
August 3rd, 2017, 2:02 pm
Forum: Special brand filaments
Topic: Has anyone used NinjaTek Cheetah?
Replies: 9
Views: 210

Re: Has anyone used NinjaTek Cheetah?

Yes but you may get some drips, another thing to do is add a little sewing machine oil to reduce filament friction in the Bowden tube, the nozzle heat is high enough to burn it off and I've not noticed any real degradation of the printed part.
by Izzy
August 3rd, 2017, 2:25 am
Forum: Special brand filaments
Topic: Has anyone used NinjaTek Cheetah?
Replies: 9
Views: 210

Re: Has anyone used NinjaTek Cheetah?

Looking at the spec it has a narrow temperature range but it is likely that it would print from 220,
Speed wise I would stick to 30mm/s for all and reduce retractions to about 1- 2mm enough to take the pressure off.
by Izzy
August 2nd, 2017, 3:04 pm
Forum: Simplify 3D
Topic: Simplify3d basic guide
Replies: 105
Views: 9222

Re: Simplify3d basic guide

In S3D, On the machine control panel there are 3 macro buttons you can program, I did set them for atomic clean temperatures so Macro 1was heat nozzle to 210, macro 2 was heat nozzle to 96. Was ideal for atomic cleaning when having to do a lot of cleans with a messy filament. But because i didn't kn...
by Izzy
August 2nd, 2017, 2:41 pm
Forum: Special brand filaments
Topic: Has anyone used NinjaTek Cheetah?
Replies: 9
Views: 210

Re: Has anyone used NinjaTek Cheetah?

I've printed with NinjaFlex and semiflex but not cheetah, yet ;-)
by Izzy
August 1st, 2017, 3:55 pm
Forum: Simplify 3D
Topic: Simplify3d basic guide
Replies: 105
Views: 9222

Re: Simplify3d basic guide

probably one for neotko but has anybody got an idiots guide to programming and saving the micros?
and does anybody know if it is possible to turn off the head cooling fan (on the Wanhao Di3+) its G-code after the print has finished. Cheers, Izzy
by Izzy
July 28th, 2017, 5:21 pm
Forum: Special brand filaments
Topic: Now igus makes filaments....
Replies: 2
Views: 114

Re: Now igus makes filaments....

I've tried the 170 and 180 but had problems with bed adhersion and layer adhesion, will try them again to see if I can get some success this time.
by Izzy
July 25th, 2017, 4:45 pm
Forum: Cura
Topic: Use less PVA
Replies: 6
Views: 181

Re: Use less PVA

I'm going to download it next week, I'm up to my mother in laws on Thursday and will also be picking up the parts to service all my shafts, bearings, belts and pullyies etc.
by Izzy
July 25th, 2017, 4:43 pm
Forum: General Questions
Topic: Keeps clogging, filament pulls out faster than stepper motor pushes
Replies: 6
Views: 218

Re: Keeps clogging, filament pulls out faster than stepper motor pushes

Another good bit of kit is an electric adjustable heat hot air gun, I've used it a couple of time to help unclog micro nozzle of 0.1 and 0.15mm, a lot easier to use than a flame. You can precisely control the heat to soften and remove.
by Izzy
July 19th, 2017, 3:43 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: UM2 service parts / upgrade.
Replies: 8
Views: 262

Re: UM2 service parts / upgrade.

I can't see the details in the link,
The thread talks about tin and non tin side from the float glass manufacturing but I can see a link to the improved flatness glass.
Sorry to be blonde, ;-)
by Izzy
July 19th, 2017, 2:47 pm
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: UM2 service parts / upgrade.
Replies: 8
Views: 262

Re: UM2 service parts / upgrade.

Where abouts did you get your glass and what's the details etc?

Go to advanced search