Search found 3332 matches

by LePaul
April 24th, 2019, 9:23 am
Forum: General Discussion
Topic: What is everyone doing
Replies: 9
Views: 108

Re: What is everyone doing

To Roberts_Clif 's points... How is a newbie supposed to have an inkling of a clue on the science of stepper driver voltage? I mean, do you know the atomic weight of how much water to use to prepare your coffee each morning? I mean, your response is just a bit flip. Like "Everyone" should know stepp...
by LePaul
April 23rd, 2019, 9:59 am
Forum: General Discussion
Topic: What is everyone doing
Replies: 9
Views: 108

Re: What is everyone doing

Well the FT-6 has been fun and challenging I'm sure the old age is part of it, GrueMaster :) I'm very detail oriented and will follow instructions to the letter. This printer's instructions certainly has a lot of areas that need additional steps and some more clarity. I was asked to offer my detaile...
by LePaul
April 21st, 2019, 10:40 pm
Forum: General Discussion
Topic: What is everyone doing
Replies: 9
Views: 108

Re: What is everyone doing

Trying to get my FolgerTech FT-6 reliable :)
by LePaul
April 11th, 2019, 10:23 am
Forum: Wireless Printing and Controllers
Topic: Octopi not showing webcam stream
Replies: 14
Views: 538

Re: Octopi not showing webcam stream

Good question for the Octoprint forum...I read a lot over there on their discussion board!
by LePaul
April 10th, 2019, 9:23 am
Forum: Wireless Printing and Controllers
Topic: Desktop enviroment for Octopi?
Replies: 7
Views: 217

Re: Desktop enviroment for Octopi?

Well no, just stay on topic to the question?
by LePaul
April 9th, 2019, 12:33 pm
Forum: Wireless Printing and Controllers
Topic: Octopi not showing webcam stream
Replies: 14
Views: 538

Re: Octopi not showing webcam stream

Have you tried a sudo apt-get update via terminal?
by LePaul
April 9th, 2019, 12:30 pm
Forum: Wireless Printing and Controllers
Topic: Desktop enviroment for Octopi?
Replies: 7
Views: 217

Re: Desktop enviroment for Octopi?

Well its like this if you are standing by at the Raspberry Pi with Octoprint you must be standing by the 3D Printer and it own controls. I think that it would be redundant to have a screen on Octoprint and also have a screen on your 3D Printer. However if you had an extra Raspberry Pi 3 you could m...
by LePaul
April 9th, 2019, 12:27 pm
Forum: Creality CR-10 Large Scale 3D Printer
Topic: problems reaching Temperature.
Replies: 6
Views: 414

Re: problems reaching Temperature.

How is any of that remotely related to the original question on the CR-10?
by LePaul
April 4th, 2019, 10:29 pm
Forum: Firmware
Topic: Marlin 1.1.9 full menus
Replies: 0
Views: 190

Marlin 1.1.9 full menus

It looks like the default is the simple menus....but I can't find where to get EVERYTHING to show, for example the babystepping and so forth

I did make sure M500 was enabled and things like that.

But I sure hate that default short menu!
by LePaul
April 4th, 2019, 10:26 pm
Forum: Creality CR-10 Large Scale 3D Printer
Topic: problems reaching Temperature.
Replies: 6
Views: 414

Re: problems reaching Temperature.

It's a DC bed on the CR-10 / CR-10S 12v takes a long time! (That's why the Tevo Tornado that came out after the CR-10 craze was so popular, having an AC bed that heats up in about a minute) Insulating could help but you'll still struggle given the power You might want to consider upgrading to an AC ...
by LePaul
April 4th, 2019, 1:48 pm
Forum: Creality CR-10 Large Scale 3D Printer
Topic: CR 10S Extruder Help!
Replies: 3
Views: 172

Re: CR 10S Extruder Help!

I don't know what an MKS Robin Lite is?

I use the Unified Firmware made by TH3D
https://www.th3dstudio.com/knowledgebas ... e-package/
by LePaul
April 4th, 2019, 1:46 pm
Forum: General 3D Printing Conversation
Topic: Problem with Heatbed Assembly for Tevo Tarantula
Replies: 3
Views: 222

Re: Problem with Heatbed Assembly for Tevo Tarantula

GrueMaster wrote:
April 4th, 2019, 9:58 am
I know @LePaul has one. Maybe he can help.
I have a Tevo Tornado
by LePaul
April 2nd, 2019, 10:51 am
Forum: Creality CR-10 Large Scale 3D Printer
Topic: [SOLVED] CR10S Marlin Firmware - arvdude vs bossac?
Replies: 17
Views: 578

Re: [SOLVED] CR10S Marlin Firmware - arvdude vs bossac?

Start a thread in the Octoprint section, we can probably help you
by LePaul
April 1st, 2019, 10:31 am
Forum: Off Topics!
Topic: Thingiverse
Replies: 1
Views: 222

Re: Thingiverse

And searchable!
by LePaul
April 1st, 2019, 10:31 am
Forum: General 3D Printing Conversation
Topic: Cocoon Create Profile for Cura V4
Replies: 24
Views: 625

Re: Cocoon Create Profile for Cura V4

I can't recall what it's called in Cura...maybe Support Top Distance...or roof....support interface? But you can set how the support "touches" the layer it is supporting for a smoother surface upon removal

Go to advanced search