Search found 3420 matches

by LePaul
November 5th, 2019, 3:51 pm
Forum: Show off your latest print
Topic: Show off My latest Print
Replies: 176
Views: 64071

Re: Show off My latest Print

Nice groot
by LePaul
November 5th, 2019, 3:50 pm
Forum: Micro 3D Printers
Topic: Anyone with an M3D printer?
Replies: 4
Views: 4172

Re: Anyone with an M3D printer?

The UM2Go has always been one of those little printers I would have like to have had. I honestly have no use for it but with the Ultimaker build quality, it would certainly do some good prints
by LePaul
November 5th, 2019, 3:49 pm
Forum: Creality Large Scale 3D Printers
Topic: MAXTEMP BED Error
Replies: 5
Views: 500

Re: MAXTEMP BED Error

We had a board do this recently on a CR-10S 500 at work. We thought it might be a bad thermosistor then the bed temp started reading wrong too.

New board was the only real solution. I was surprised the board had to go but something on it just isn't right.
by LePaul
November 5th, 2019, 3:47 pm
Forum: Feedback, suggestions and more
Topic: Cooling Fan Speed vs Strength
Replies: 5
Views: 1811

Re: Cooling Fan Speed vs Strength

He has a good channel. I like his videos...especially his advice on more perimeters rather than more infill for strength
by LePaul
October 16th, 2019, 3:45 pm
Forum: General 3D Printing Conversation
Topic: Moisture Eliminators
Replies: 4
Views: 657

Re: Moisture Eliminators

I've been meaning to get and use a dryer for my old stacks of Ultimaker brand PLA
by LePaul
October 16th, 2019, 3:43 pm
Forum: Original Prusa i3 MK Series printer
Topic: [News] Prusa i3 MK2 release!
Replies: 22
Views: 11671

Re: [News] Prusa i3 MK2 release!

That's out of my control :)
by LePaul
October 16th, 2019, 3:42 pm
Forum: General 3D Printing Conversation
Topic: Creality CR-10 S4 or Ender-5 Plus, Which To Get?
Replies: 2
Views: 513

Re: Creality CR-10 S4 or Ender-5 Plus, Which To Get?

I suggest people learn on something smaller or well known...like a CR-10S. Get the hang of using the slicer, printing and then as you gain experience , then move on to something larger
by LePaul
October 11th, 2019, 10:59 am
Forum: Help me fix this print!
Topic: Problem with surface finish
Replies: 3
Views: 851

Re: Problem with surface finish

I think that's Combing and Cura should give you an option of something like "Not on top" or the like
by LePaul
October 11th, 2019, 10:57 am
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: UM2 and IRobertI feeder - filament snaps behind bearing
Replies: 2
Views: 1099

Re: UM2 and IRobertI feeder - filament snaps behind bearing

How annoying

I didn't go that route, i did the [expensive] UM2+ extruder upgrade. That's worked very well.
by LePaul
October 11th, 2019, 10:54 am
Forum: Ultimaker 2 / Ultimaker 2+ / Extended & Go
Topic: UM2 Heater Blocks
Replies: 1
Views: 273

Re: UM2 Heater Blocks

Good question....I wondered about upgrades to my UM2+ With so many out there, I was curious if someone offered some hot end upgrades or even a board upgrade to utilize better drivers (i.e. no Salmon Skin effect)
by LePaul
October 11th, 2019, 10:53 am
Forum: General Discussion
Topic: Largest 3D Prints and Printer
Replies: 2
Views: 737

Re: Largest 3D Prints and Printer

I don't think our client would allow that :)
by LePaul
October 10th, 2019, 2:10 pm
Forum: General Discussion
Topic: Largest 3D Prints and Printer
Replies: 2
Views: 737

Largest 3D Prints and Printer

Ok, I can finally reveal what's been going on at work, on a project I have been involved with!

https://www.newscentermaine.com/article ... c1a074e25a

New link!
by LePaul
October 3rd, 2019, 2:07 pm
Forum: Special brand filaments
Topic: ColorFabb_HT Filament
Replies: 3
Views: 2110

Re: ColorFabb_HT Filament

Well that's totally up to the consumer....I didn't look far and high for something that could withstand 100C. I know ColorFabb makes good stuff and supports what they sell. I went back and forth with their support to fine tune my settings. I'm not sure another filament maker would do that
by LePaul
September 24th, 2019, 5:26 pm
Forum: General Discussion
Topic: Summer is Over
Replies: 3
Views: 511

Re: Summer is Over

Summer went quick!
Then the fall colds hit quick over here!

With the new job and all my travels, I haven't done much to my own printers lately...asides print!

And speaking of...I'm off to Tampa next week for the Boat Builder show. We're doing a presentation on 3D printing!
by LePaul
September 18th, 2019, 9:57 pm
Forum: News and Announcements
Topic: Added Chat (mChat)
Replies: 3
Views: 3998

Re: Added Chat (mChat)

Roberts_Clif wrote:
September 11th, 2019, 9:09 am
Have looked everywhere, can not find how to use this mChat.

Where do I read about it.
Newer versions didnt support it

Go to advanced search