Search found 395 matches

by Roberts_Clif
August 14th, 2018, 10:33 am
Forum: Other Slicing programs
Topic: Triangulatica
Replies: 2
Views: 19

Re: Triangulatica

$10,000 dollars a year far exceeds my budget for all my hobbies to say the least for Fused Layer Modeling/Fused Deposition Modeling Printer.

Can a single 3D Printer working 24 hours a day print fast enough to make a viable profit with this added overhead only printing 8760 hours a year.
by Roberts_Clif
August 9th, 2018, 12:29 pm
Forum: General Questions
Topic: Heater voltage
Replies: 1
Views: 100

Re: Heater voltage

I do no believe I have seen a 3DP15

01_01510371-901b-41b4-bda5-8e371ac68368.jpg


However If your power supply is a 12v buy 12V heater if Supply is 24V buy 24V heater

I started with a 3DP11 and 3DP12 though upgrades makes them both considered 3DP17's with Auto level and Filament Monitors
by Roberts_Clif
August 9th, 2018, 11:10 am
Forum: RepRap Printers
Topic: Cura - Rafts
Replies: 2
Views: 63

Re: Cura - Rafts

Yea this could be true, though it is tons easier to setup and learn without something else causing print errors.

Then changes can be incorporated into the Newer versions of Cura 3.4.1 or vise versa.
by Roberts_Clif
August 9th, 2018, 9:22 am
Forum: RepRap Printers
Topic: Cura - Rafts
Replies: 2
Views: 63

Cura - Rafts

Today I an try to learn about the raft settings using Cura 15.04.6. Raft.jpg Would like to know if anyone has information as to what the best settings would be for a raft. Lets say Best adhesion, easiest part removal and smoothest model bottom layer as examples or am I overthinking this. I believe t...
by Roberts_Clif
August 3rd, 2018, 8:00 am
Forum: Software and Firmware Discussion
Topic: Updating HIC 3DP-03 to Marlin 1.1.X
Replies: 5
Views: 205

Re: Updating HIC 3DP-03 to Marlin 1.1.X

Marlin 1.1.5 Configuration.h

Took the liberality of making most changes take a look see if I missed anything.

I used WinMerge to make the changes.

Configuration.h
(62.01 KiB) Downloaded 2 times
by Roberts_Clif
August 2nd, 2018, 9:08 pm
Forum: Software and Firmware Discussion
Topic: Updating HIC 3DP-03 to Marlin 1.1.X
Replies: 5
Views: 205

Re: Updating HIC 3DP-03 to Marlin 1.1.X

Are planning to setup the auto bed leveling?

Manual using Z-End Stop Switch ( https://github.com/MarlinFirmware/Marli ... d-Leveling )
Auto bed leveling using a Z-Proximity sensor ( http://marlinfw.org/docs/features/auto_ ... eling.html )
by Roberts_Clif
August 2nd, 2018, 5:43 pm
Forum: Software and Firmware Discussion
Topic: Updating HIC 3DP-03 to Marlin 1.1.X
Replies: 5
Views: 205

Re: Updating HIC 3DP-03 to Marlin 1.1.X

Do you have your original firmware source code? I have a 3DP11 and a 3DP12 and started with Chip Luck's firmware presently using Marlin 1.1.5. Thou have configured all Marlin 1.1.X Post a Link or your configuration.h file, we have many Hictop users here and can get you on the correct path. Not sure ...
by Roberts_Clif
August 2nd, 2018, 10:27 am
Forum: General Discussion
Topic: It's a bit too quiet in here...how is everyone?
Replies: 10
Views: 622

Re: It's a bit too quiet in here...how is everyone?

I 3D Printed some Couch Lifts, for some reason the couch is about 3 inches to low this make it next to impossible for older people to stand up. Well they can stand up they just have to rock back and forth until they get enough momentum to finally rock to their feet. So I went to ThinkerCad and quick...
by Roberts_Clif
August 1st, 2018, 4:46 pm
Forum: General Discussion
Topic: It's a bit too quiet in here...how is everyone?
Replies: 10
Views: 622

Re: It's a bit too quiet in here...how is everyone?

We've been on a hot/muggy/humid streak over here, which is the usual for this part of Maine. In other news, my YouTube Channel finally pushed past 1,000 Subscribers, so that's a really good achievement for me! I'm having a lot of fun doing it, still learning the finer points of editing...but I like...
by Roberts_Clif
August 1st, 2018, 7:46 am
Forum: General Discussion
Topic: It's a bit too quiet in here...how is everyone?
Replies: 10
Views: 622

Re: It's a bit too quiet in here...how is everyone?

I hear you Grue Master, and the smoke makes it so you want to limit the extra fumes from the 3D Printers. I have still been 3D Printing as the temperature in the shop area where 3D Printing occurs is still in the 80s Fahrenheit OK for 3D Printing. Sure Glad I do not have to be in the room during the...
by Roberts_Clif
July 30th, 2018, 9:19 pm
Forum: General Discussion
Topic: It's a bit too quiet in here...how is everyone?
Replies: 10
Views: 622

Re: It's a bit too quiet in here...how is everyone?

For several day now Eastern Washington and Oregon have spiked over 100F degrees and will continue thru Wednesday.
This is when the temperature is suppose to drop back to high 90's where we can get back to a normal double digit weather.
by Roberts_Clif
July 28th, 2018, 2:02 pm
Forum: General 3D Printing Conversation
Topic: Noob with tons of questions
Replies: 19
Views: 259

Re: Noob with tons of questions

You are Most Welcome. The Forum is here to help you get more confused than you were before you started. Whoops! I mean we are he to help you learn 3D Printing from the basics to the most extreme advanced levels. While you are learning, along the way you can also help others with what you have learne...
by Roberts_Clif
July 27th, 2018, 2:55 pm
Forum: General 3D Printing Conversation
Topic: Noob with tons of questions
Replies: 19
Views: 259

Re: Noob with tons of questions

Well! I have two Hictop 270 x 220 x 190 both were around $200.00 both have Printed everything have tried to Print.
I even printed a 100mm bridging test print to see if it could be done by this 3D Pinter, with complete success.

https://www.thingiverse.com/make:373631
by Roberts_Clif
July 27th, 2018, 7:59 am
Forum: General 3D Printing Conversation
Topic: Noob with tons of questions
Replies: 19
Views: 259

Re: Noob with tons of questions

Now that you have selected your first 3D Printer TEVO Tarantula 3D Printer - Official FULL MANUAL Get familiar before it arrives this will make the assemble go smoother.

Go to advanced search