Search found 1143 matches
- January 15th, 2021, 3:38 pm
- Forum: Help me fix this print!
- Topic: Your modal is not manifold - error message
- Replies: 4
- Views: 396
Re: Your modal is not manifold - error message
Do not have an answer your last question.
- January 4th, 2021, 7:48 am
- Forum: Help me fix this print!
- Topic: Your modal is not manifold - error message
- Replies: 4
- Views: 396
Re: Your modal is not manifold - error message
I opened and in the same happened had to scale down from 100 % to 25.4% still was over my bed size so scaled the Z- to my max height 190mm. I sliced the model while it was laying on its side at 25.4% two oval shaped orbs showed the lower third of the model and the top third. For some reason the midd...
- January 2nd, 2021, 8:55 am
- Forum: Cura
- Topic: Issue with embossed feature - Cura
- Replies: 4
- Views: 274
Re: Issue with embossed feature - Cura
Your text is quite small if it was larger it would be easier to print with a 0.4mm nozzle, I sliced it with PrusaSlicer 2.3.0 rc2 shown below. Do not know if the 0.4mm nozzle will print the embossed text unless the text line width was at least 0.4mm though. Image1.jpg Using any slicer you could try ...
- December 28th, 2020, 8:49 am
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 6
- Views: 4372
Re: Old Brittle Filament
1800 views and no comments seems strange. Not really there are so many posts on this subject most already know all the information My enclosure is heated. With the air heated the filament temperature is higher making my filament more flexible so I do worry about filament breaking during printing. I...
- December 26th, 2020, 3:37 pm
- Forum: Help me fix this print!
- Topic: Printer printing where it shouldn’t
- Replies: 5
- Views: 3408
Re: Printer printing where it shouldn’t
Can you show a screen capture of the Model sliced, I assume you are using supports everywhere an showing the supports will show this.
When using Prusaslicer you can add a modifier that you use can to tell the slicer not to add supports around the holes.
If you need help we can help you get it setup.
When using Prusaslicer you can add a modifier that you use can to tell the slicer not to add supports around the holes.
If you need help we can help you get it setup.
- December 25th, 2020, 2:33 pm
- Forum: News and Announcements
- Topic: Happry Holidays
- Replies: 1
- Views: 1049
Happry Holidays
We wish you a very Happy Holiday season and a peaceful and prosperous New Year.
An Thank You for all your posts.
From Roberts_Clif
An Thank You for all your posts.
From Roberts_Clif
- December 23rd, 2020, 3:54 pm
- Forum: Creality Large Scale 3D Printers
- Topic: Creality CR10 S5 home issue
- Replies: 5
- Views: 1099
Re: Creality CR10 S5 home issue
Sounds like it could be and End_Stop switch/ Sensor. Have you tried to sending a M119 to check the status all end-stops switches/sensors.
What is the Z-Axis number when the nozzle hits the bed.
What is the Z-Axis number when the nozzle hits the bed.
- December 22nd, 2020, 9:47 am
- Forum: Cura
- Topic: Arachne engine alpha
- Replies: 1
- Views: 389
Arachne engine alpha
Arachne engine alpha New Settings Variable Line Strategy : How the walls are spread over the available space. Central Deviation : Will print all walls at the nominal line width except the central one(s), causing big variations in the center but very consistent outsides. Distributed : Distributes th...
- December 21st, 2020, 9:20 am
- Forum: Cura
- Topic: Is there a way to print out Cura's setting under Profile?
- Replies: 8
- Views: 828
Re: Is there a way to print out Cura's setting under Profile?
That's strange I open mine with Notepad++
Are we talking about another file.
Are we talking about another file.
- December 20th, 2020, 5:47 pm
- Forum: Cura
- Topic: Cura cutting off top portion of a round shaft part?
- Replies: 7
- Views: 668
Re: Cura cutting off top portion of a round shaft part?
Attach the STL shaft I will print it to see if Prusa slicer does a better job.
- December 20th, 2020, 4:29 pm
- Forum: Cura
- Topic: Cura cutting off top portion of a round shaft part?
- Replies: 7
- Views: 668
Re: Cura cutting off top portion of a round shaft part?
What layer height are you using to print shaft. I would use 0.12mm it takes longer though will give you a stronger shaft.
- December 20th, 2020, 2:28 pm
- Forum: Firmware
- Topic: Ender 5 plus
- Replies: 3
- Views: 669
Re: Ender 5 plus
Thank You
- December 20th, 2020, 2:22 pm
- Forum: Cura
- Topic: Print Multiple of same part in one set up One at a time?
- Replies: 5
- Views: 587
Re: Print Multiple of same part in one set up One at a time?
You are Most Welcome.
- December 20th, 2020, 2:10 pm
- Forum: Cura
- Topic: Need Help with Supports
- Replies: 23
- Views: 1435
Re: Need Help with Supports
Thank You LePaul
Which plugin do you use to make the supports look so good.
Which plugin do you use to make the supports look so good.
- December 20th, 2020, 7:32 am
- Forum: Firmware
- Topic: Ender 5 plus
- Replies: 3
- Views: 669
Ender 5 plus
Hello forum
I am Helping a Ender5 plus user who recently purchased a Creality 32bit Silent Controller Board,
The BL Touch will not work on his Ender 5 plus
Does anyone Have a Marlin firmware configured for this configuration.
I am Helping a Ender5 plus user who recently purchased a Creality 32bit Silent Controller Board,
The BL Touch will not work on his Ender 5 plus
Does anyone Have a Marlin firmware configured for this configuration.