Search found 21 matches

by rokhdrone1uk
November 22nd, 2016, 5:06 pm
Forum: General Questions
Topic: elephant foot, leveling bed, zsteps
Replies: 15
Views: 22071

Re: elephant foot, leveling bed, zsteps

Izzy wrote:I would try slowing down to about 45mm/s and trying the 1st level at 200um (0.2mm)
Slowing down the print speed or movement?
by rokhdrone1uk
November 22nd, 2016, 3:20 pm
Forum: General Questions
Topic: elephant foot, leveling bed, zsteps
Replies: 15
Views: 22071

Re: elephant foot, leveling bed, zsteps

Sure is, I've have been using this since i got my Printer, never used any other software
by rokhdrone1uk
November 22nd, 2016, 3:13 pm
Forum: General Questions
Topic: elephant foot, leveling bed, zsteps
Replies: 15
Views: 22071

Re: elephant foot, leveling bed, zsteps

What material are you printing, what adhesion are you using and what is the thickness of your 1st level, and the 1st layer speed? Hi Izzy, I am using ABS, my Bed Temp is 95-100, Extrude Temp 245 I'm using LULZBOT PEI Sheet, which I've had no issues with before. Primary Layer H - 0.1200 http://www.3...
by rokhdrone1uk
November 22nd, 2016, 2:36 pm
Forum: General Questions
Topic: elephant foot, leveling bed, zsteps
Replies: 15
Views: 22071

Re: elephant foot, leveling bed, zsteps

Hey all,

Hope you don't mind me jumping in on this.

But I've finally got my printer working, but for some reason.

The Skirt / Brim isn't add-hearing to the bed, the main part is but that is leaving me with a mess to clear before the print starts.

Anyone have any clues??
by rokhdrone1uk
November 17th, 2016, 1:56 pm
Forum: CAD and 3D Modeling Software
Topic: 3Ds Max or MAYA
Replies: 2
Views: 8778

3Ds Max or MAYA

So I use both 3Ds Max and Maya to create and design models etc.

But I seem to be having an issue with Max output models in OBJ but not in Maya.

Do anyone else use Max OBJ? if so how you setting up your model and then exporting?

Are you using STL or OBJ?

Thanks

Stu
by rokhdrone1uk
November 17th, 2016, 1:51 pm
Forum: Software and Firmware Discussion
Topic: Uploading/flashing Marlin to your Hic i3 (or other)
Replies: 40
Views: 156644

Re: Uploading/flashing Marlin to your Hic i3 (or other)

Hi rokhdrone1uk, Great to read that it is working now. I am waiting for mine to be delivered impatiently. I have read many articles and went to the conclusion that I will go for a dual fan system, remove the motor from the x-carriage and place it on the right vertical axe. http://www.thingiverse.co...
by rokhdrone1uk
November 16th, 2016, 4:05 pm
Forum: Software and Firmware Discussion
Topic: Uploading/flashing Marlin to your Hic i3 (or other)
Replies: 40
Views: 156644

Re: Uploading/flashing Marlin to your Hic i3 (or other)

Hey Chip, so i have been trying to use your firmware but im having a few issues. Yes these are mine and not your firmware, thanks it is amazing but my LCD has stopped working and also im getting a Heater_ID:Bed error You have any ideas. Im using a stock 3DP12 Hic i3. Hope your able to help. My prin...
by rokhdrone1uk
November 15th, 2016, 1:26 pm
Forum: Software and Firmware Discussion
Topic: Uploading/flashing Marlin to your Hic i3 (or other)
Replies: 40
Views: 156644

Re: Uploading/flashing Marlin to your Hic i3 (or other)

Hi Chip, so I have got the printer working and was hoping I could use your .config files etc. You able to email them or share a link. Thanks I received this .hex code form Hictop today, but i'm having a auto home direction issue Moving right and not left towards the micro switch.. How do i change th...
by rokhdrone1uk
November 10th, 2016, 1:51 pm
Forum: Software and Firmware Discussion
Topic: HIC i3 - current firmware development information
Replies: 152
Views: 241712

Re: HIC i3 - current firmware development information

Does moving the x-axis via the LCD result in the same movement ( (+) = Left; (-) = Right)? If so, your stepper pins are backwards. Either swap them manually (preferred) or change the setting in Marlin: #define INVERT_X_DIR true If it is only occurring in Simplify3d, check your settings and see what...
by rokhdrone1uk
November 7th, 2016, 3:19 pm
Forum: Software and Firmware Discussion
Topic: HIC i3 - current firmware development information
Replies: 152
Views: 241712

Re: HIC i3 - current firmware development information

Chip, Ive just updated my Firmware and now im getting a Heater_ID:Bed Error in Adruino and also my LCD isnt working?? When i try to flash to my printer it is saying old Config.h file..... Im using a stock Hic i3 3dP12 - the only thing ive done is upgrade my extruder with the Infill3D / e3D V6. Do i...
by rokhdrone1uk
November 7th, 2016, 1:55 pm
Forum: Software and Firmware Discussion
Topic: Uploading/flashing Marlin to your Hic i3 (or other)
Replies: 40
Views: 156644

Re: Uploading/flashing Marlin to your Hic i3 (or other)

I received this .hex code form Hictop today, but i'm having a auto home direction issue Moving right and not left towards the micro switch..

How do i change this?
by rokhdrone1uk
November 6th, 2016, 4:24 pm
Forum: Software and Firmware Discussion
Topic: HIC i3 3DP-18 Firmware
Replies: 9
Views: 17623

Re: HIC i3 3DP-18 Firmware

redrx0 wrote:I think you need to change,
#define TEMP_SENSOR_BED 0
To
#define TEMP_SENSOR_BED 3
If you have a factory bed & sensor, I think.
Thanks i will give that a go, any idea on how i fix the blank LCD screen, was working before the update.
by rokhdrone1uk
November 6th, 2016, 2:40 pm
Forum: Show off your latest print
Topic: Show off My latest Print
Replies: 176
Views: 202791

Re: Show off My latest Print

Thanks Paul :) much appreciated

Great Forum btw, :)
by rokhdrone1uk
November 6th, 2016, 2:30 pm
Forum: Show off your latest print
Topic: Show off My latest Print
Replies: 176
Views: 202791

Re: Show off My latest Print

Infill 3d Upgrade for 3DP12

This was what ive printed, but needing some help with my Config.h file

Thanks

Stu
by rokhdrone1uk
November 6th, 2016, 2:25 pm
Forum: Software and Firmware Discussion
Topic: Uploading/flashing Marlin to your Hic i3 (or other)
Replies: 40
Views: 156644

Re: Uploading/flashing Marlin to your Hic i3 (or other)

Hey Chip, so i have been trying to use your firmware but im having a few issues. Yes these are mine and not your firmware, thanks it is amazing but my LCD has stopped working and also im getting a Heater_ID:Bed error You have any ideas. Im using a stock 3DP12 Hic i3. Hope your able to help. My print...

Go to advanced search